X-108 Info Xiegu X-108G Outdoor QRP-Transceiver - files and mods

Discussion in 'X-108' started by DO7PSL, Jan 19, 2016.

  1. X-108 Member
    katman374
    Offline

    katman374 Chef-Boarder

    Messages:
    9
    Likes Received:
    1
    Trophy Points:
    1
    yes it does
     
  2. X-108 Member
    Gilles VE2GIQ
    Offline

    Gilles VE2GIQ Chef-Boarder

    Messages:
    9
    Likes Received:
    0
    Trophy Points:
    1
    Verified User:
    YES
    Rufzeichen/Call:
    ve2giq
    Xiegu X108G Outdoor version standard PTT out procedure.
    Check this procedure if you want to add a standard PTT out for your linear amplifier.
     

    Attached Files:

    • Winner Winner x 1
  3. X-108 Member
    K7RAN
    Offline

    K7RAN Beginner

    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    K7RAN
    I wonder if the R76 removal mod (wideband) works on the CS108G+ version as well?
     
  4. X-108 Member
    manuelg
    Offline

    manuelg Junior Boarder

    Messages:
    6
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    ea4cgf
    december 2016 1.00.04 firmware for an x108g outdoor with CXG 10xxx serial number

    remember to first backup your settings power on+press F1 and write down everythung. I would do the same thing with power on+press F2

    Only then update the firmware
     

    Attached Files:

  5. X-108 Member
    DH3SBW
    Offline

    DH3SBW Beginner

    Messages:
    3
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    DH3SBW
    Hat jemand eine Anleitung, wie ich das Gerät X108G am besten auseinander bauen kann? Würde gerne die tx Erweiterung basteln ..
    VY 73
     
    Last edited: Sep 28, 2017
  6. X-108 Member
    Bryancaddy
    Offline

    Bryancaddy Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    k7bat
    Hello all. I have an issue that I am sure is something that I did with the firmware. Radio was working, then I updated to v2.00.1_build002 and I dont hear anything. SQL is 0, so its not that.. my antenna is good, I am using it on my IC7300 with out issue. I use this little guy for camping, but I think its dead now. I got all my numbers, put them in and no joy.

    I could have screwed something up... hard to tell. I have tried downgrading, and upgrading.. no joy for sound. display comes on, looks good.

    Thanks for reading this. ;)
     
  7. X-108 Member
    Timur
    Offline

    Timur Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    UB9ODT
    Good day!
    After upgrading to version 1.00.4, the sound became quiet, and the stations are not listening. Settings F1 correspond to the saved. Tell me how to return the sound?
     
  8. X-108 Member
    Henry Hobart
    Offline

    Henry Hobart Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    n3lvf
    mine did same thing
     
  9. X-108 Member
    Henry Hobart
    Offline

    Henry Hobart Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    n3lvf
    one firmware gives me a display but no sound,,other firmware gives me a blank screen....my rig is 01 serial number,i got that part right..i do a lot on computers at work.....i am not out tho,,.i paid 100 bucks for this at a fleemarket..knowing the transmitt section was out..all should note where you order mosfets ,the finals..one company off ebay that sells replacement mosfets , thay are bigger than orig ones...may try to contact somone from mfg...but dont have a lot of hopes..
     
  10. X-108 Member
    Elsibert
    Offline

    Elsibert Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    LA7HKA
    Hi im new here.
    Just got my X108G outdoor radio. It has the FW v1.00.4 May 2017. The radio does not RX or TX, do anyone have suggestions of what to do?
     
  11. X-108 Member
    Elsibert
    Offline

    Elsibert Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    LA7HKA
    Hello again.
    Is it possible the system settings are wrong from the factory?
     
  12. X-108 Member
    Elsibert
    Offline

    Elsibert Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    LA7HKA
    Trying to contact xiegu.
     
  13. X-108 Member
    F8LDxr
    Offline

    F8LDxr Beginner

    Messages:
    1
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    Kb3exf
    Hi new here just got my x108g and AM swings in reverse can anyone help with the outdoor version, the AM reverse modulation? How do i reverse this crime against AM opperation?
    Thanks in advance for any info at all. 73s hope to hear these radios on the air.
     
  14. X-108 Member
    Henry Hobart
    Offline

    Henry Hobart Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    n3lvf
    Thay probley all do that..mine also .i also noticed the noise blanket don't work at all...i have a parts radio now...i have used AM on 10 meter and even with backwards swing have got good reports..if ya put a peak reading watt meter on you will have forward swing..best73
     
  15. X-108 Member
    Elsibert
    Offline

    Elsibert Beginner

    Messages:
    4
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    LA7HKA
    Finaly got a mail from xiegu. They said to open the radio and check if the antenna connector is is broken(bad solder).
    The antenna connector is just fine, no bad solder or anything. Since i allready had open the radio, i traced the signal through bpf's to the mixer. I seems like there is no local oscillator signal to the mixer? The TCXO works fine, strong 26MHz signal. Is there anybody that have the new outdoor version 0,5ppm 26MHz TCXO that have the same problem?
     
  16. X-108 Member
    OA4LDR
    Offline

    OA4LDR Chef-Boarder

    Messages:
    13
    Likes Received:
    3
    Trophy Points:
    3
    Rufzeichen/Call:
    Tito
    [QUOTE = "wgoodf, publicación: 443, miembro: 88"] Hola chicos - Acabo de registrarme como tengo un X108G bloqueado.
    Estaba teniendo un extraño problema de software: la radio se bloqueaba cuando presionaba el botón para dividir el trabajo y, a veces, giraba la perilla y la frecuencia seguía cambiando después de retirar mi mano.
    De todos modos, contacté a Xiegu y me enviaron el archivo V1 build 24. Lo instalé como las instrucciones y ahora la radio está bloqueada con una pantalla blanca.

    El proceso que utilicé fue este:
    Conecto la radio a la computadora. He probado Windows XP y MacOS.
    Sostengo el botón y enciendo; llego a la pantalla de actualización.
    La radio se monta como E: - Elimino el archivo firmware.bin.
    La radio flash se borra al 100% = Flash Erase OK
    Copio el archivo: X108G_OLED_FW_V1.00_build024.xgf - a la radio. (he probado otros y solo he intentado el V2 build10.)
    Escritura flash - 137728 bytes - ¡Actualización realizada!
    Por favor reinicie su plataforma.

    Apago el equipo: desconecto el USB de la computadora, enciendo el equipo y la pantalla está blanca, sin pitido de arranque. La pequeña luz verde en el puerto del micrófono está encendida.
    Eso es todo lo que hace: la radio ahora está muerta.

    ¿Me estoy perdiendo algo o estoy haciendo algo estúpido?
    Cualquier ayuda sería muy apreciada.
    Gracias por adelantado.
    wgoodf / MM6FXZ [/ QUOTE]
    Hola saludos cordiales desde lima Perú! Después de quitar la actualización tienes que apagar el equipo,quitar el cable de voltaje encender el equipo sin el cable para ir descargues todo el voltaje que se almacena en el, luego lo apagas y le vuelves. Conectar el cable de voltaje y encenderlo nuevamente y listo regresa a la vida! Saludos cordiales OA4LDR
     
  17. X-108 Member
    OA4LDR
    Offline

    OA4LDR Chef-Boarder

    Messages:
    13
    Likes Received:
    3
    Trophy Points:
    3
    Rufzeichen/Call:
    Tito
    Espero que te sirva de ayuda! Saludos!
     
  18. X-108 Member
    Jabier
    Offline

    Jabier Beginner

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    EA2ARU
    How is possible see the serialnumber? Is possible: CXG0026 ...
     
  19. X-108 Member
    Jabier
    Offline

    Jabier Beginner

    Messages:
    2
    Likes Received:
    0
    Trophy Points:
    1
    Rufzeichen/Call:
    EA2ARU
    I have the outdoor version.
     
  20. X-108 Member
    OA4LDR
    Offline

    OA4LDR Chef-Boarder

    Messages:
    13
    Likes Received:
    3
    Trophy Points:
    3
    Rufzeichen/Call:
    Tito
    [QUOTE = "Jabier, post: 1072, member: 905"] ¿Cómo es posible ver el número de serie? Es posible: CXG0026 ... [/ QUOTE]

    Esta es mi serie !!! Y le puse está actualización del x108g v2 y el menú de servicio F1 es de 15 ítems y el menú F2 queda de esta manera se la imagen! ¡Y removí R76 que en mi modelo no lo dije y abrí los 11 metros! Aprovechar en cambiar la pila de la memoria también! Voy a seguir experimentando y les voy informando de las novedades! Voy a tratar de subir el firmware del 2017! Saludos cordiales desde Lima-Peru OA4LDR 73s
     

    Attached Files:

Share This Page